View AZ100EL31_357717.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ARIZONA MICROTEK, INC.
AZ10EL31 AZ100EL31
ECL/PECL D Flip-Flop with Set and Reset FEATURES
* * * * 475ps Propagation Delay 2.8GHz Toggle Frequency 75k Internal Input Pulldown Resistors Direct Replacement for ON Semiconductor MC10EL31 & MC100EL31 PACKAGE AVAILABILITY PACKAGE SOIC 8 SOIC 8 T&R SOIC 8 T&R SOIC 8 SOIC 8 T&R SOIC 8 T&R TSSOP 8 TSSOP 8 T&R TSSOP 8 T&R TSSOP 8 TSSOP 8 T&R TSSOP 8 T&R PART NO. AZ10EL31D AZ10EL31DR1 AZ10EL31DR2 AZ100EL31D AZ100EL31DR1 AZ100EL31DR2 AZ10EL31T AZ10EL31TR1 AZ10EL31TR2 AZ100EL31T AZ100EL31TR1 AZ100EL31TR2 MARKING AZM10EL31 AZM10EL31 AZM10EL31 AZM100EL31 AZM100EL31 AZM100EL31 AZTEL31 AZTEL31 AZTEL31 AZHEL31 AZHEL31 AZHEL31
DESCRIPTION
The AZ10/100EL31 is a master-slave D flip-flop with set and reset. The device is functionally equivalent to the E131 device with higher performance capabilities. With propagation delays and output transition times significantly faster than the E131, the EL31 is ideally suited for those applications that require the ultimate in AC performance. Both set and reset inputs are asynchronous, level triggered signals. Data enters the master section of the flipflop when the clock is LOW. When the clock transitions from LOW to HIGH, the data in the master section transfers into the slave section and through to the outputs. NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established. TRUTH TABLE LOGIC DIAGRAM AND PINOUT ASSIGNMENT
D L H X X X S* L L H L H R* L L L H H CLK Z Z X X X Q L H H L Undef Q H L L H Undef
S
1 S
8
VCC
Z = LOW to HIGH Transition * Pins will default low when left open
D
2
D Flip Flop
7
Q
PIN DESCRIPTION PIN S D R CLK Q, Q VCC VEE FUNCTION Set Input Data Input Reset Input Clock Input Data Outputs Positive Supply Negative Supply
CLK
3 R 4
6
Q
R
5
VEE
1630 S. STAPLEY DR., SUITE 125 * MESA, ARIZONA 85204 * USA * (480) 962-5881 * FAX (480) 890-2541 www.azmicrotek.com
AZ10EL31 AZ100EL31
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Symbol VCC VI VEE VI IOUT TA TSTG Characteristic PECL Power Supply (VEE = 0V) PECL Input Voltage (VEE = 0V) ECL Power Supply (VCC = 0V) ECL Input Voltage (VCC = 0V) Output Current --- Continuous --- Surge Operating Temperature Range Storage Temperature Range Rating 0 to +8.0 0 to +6.0 -8.0 to 0 -6.0 to 0 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc Vdc Vdc mA C C
10K ECL DC Characteristics (VEE = -4.75 to -5.5V, VCC = GND)
Symbol VOH VOL VIH VIL IIH IIL IEE 1. Characteristic
1
Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Input HIGH Current D, CLK 150 S, R 300 Input LOW Current 0.5 Power Supply Current 27 32 Each output is terminated through a 50 resistor to VCC - 2V.
Min -1080 -1950 -1230 -1950
-40C Typ
Max -890 -1650 -890 -1500
Min -1020 -1950 -1170 -1950
0C Typ
Max -840 -1630 -840 -1480 150 300
Min -980 -1950 -1130 -1950
25C Typ
Max -810 -1630 -810 -1480 150 300
Min -910 -1950 -1060 -1950
85C Typ
Max -720 -1595 -720 -1445 150 300
Unit mV mV mV mV A A mA
0.5 27 32
0.5 27 32
0.5 27 32
10K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol VOH VOL VIH VIL IIH IIH IIL IEE 1. 2. Characteristic
1,2
Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Input HIGH Current D, CLK 150 150 S, R 300 300 Input HIGH Current 150 150 Input LOW Current 0.5 0.5 0.5 Power Supply Current 27 32 27 32 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50 resistor to VCC - 2V.
Min 3920 3050 3770 3050
-40C Typ
Max 4110 3350 4110 3500
Min 3980 3050 3830 3050
0C Typ
Max 4160 3370 4160 3520
Min 4020 3050 3870 3050
25C Typ
Max 4190 3370 4190 3520 150 300 150
Min 4090 3050 3940 3050
85C Typ
Max 4280 3405 4280 3555 150 300 150
Unit mV mV mV mV A A A mA
0.5 27 32 27 32
100K ECL DC Characteristics (VEE = -4.2V to -5.5V, VCC = GND)
Symbol VOH VOL VIH VIL IIH IIH IIL IEE 1. Characteristic
1
Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Input HIGH Current D, CLK 150 S, R 300 Input HIGH Current 150 Input LOW Current 0.5 Power Supply Current 27 32 Each output is terminated through a 50 resistor to VCC - 2V.
Min -1085 -1830 -1165 -1810
-40C Typ -1005 -1695
Max -880 -1555 -880 -1475
Min -1025 -1810 -1165 -1810
0C Typ -955 -1705
Max -880 -1620 -880 -1475 150 300 150
Min -1025 -1810 -1165 -1810
25C Typ -955 -1705
Max -880 -1620 -880 -1475 150 300 150
Min -1025 -1810 -1165 -1810
85C Typ -955 -1705
Max -880 -1620 -880 -1475 150 300 150
Unit mV mV mV mV A A A mA
0.5 27 32
0.5 27 32
0.5 31 37
October 2001 * REV - 2
www.azmicrotek.com 2
AZ10EL31 AZ100EL31
100K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol VOH VOL VIH VIL IIH IIH IIL IEE 1. 2. Characteristic
1,2
Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Input HIGH Current D, CLK 150 150 S, R 300 300 Input HIGH Current 150 150 Input LOW Current 0.5 0.5 0.5 Power Supply Current 27 32 27 32 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50 resistor to VCC - 2V.
Min 3915 3170 3835 3190
-40C Typ 3995 3305
Max 4120 3445 4120 3525
Min 3975 3190 3835 3190
0C Typ 4045 3295
Max 4120 3380 4120 3525
Min 3975 3190 3835 3190
25C Typ 4045 3295
Max 4120 3380 4120 3525 150 300 150
Min 3975 3190 3835 3190
85C Typ 4045 3295
Max 4120 3380 4120 3525 150 300 150
Unit mV mV mV mV A A A mA
0.5 27 32 31 37
AC Characteristics (VEE =10E(-4.75V to -5.5V), 100E(-4.2V to -5.5V); VCC =GND or VEE =GND; VCC =10E(+4.75V to +5.5V), 100E(+4.2V to +5.5V))
Symbol fMAX tPLH / tPHL tS tH tRR tPW tr / t f Characteristic Maximum Toggle Frequency Propagation Delay to Output CLK S,R Setup Time Hold Time Set/Reset Recovery Minimum Pulse Width CLK, Set, Reset Output Rise/Fall Times Q (20% - 80%) Min 2.0 315 295 150 250 400 400 100 350 -40C Typ 2.5 465 455 0 100 200 630 630 Max Min 2.2 365 345 150 250 400 400 100 350 0C Typ 2.8 465 455 0 100 200 580 580 Max Min 2.2 375 355 150 250 400 400 100 350 25C Typ 2.8 475 465 0 100 200 590 590 Max Min 2.2 430 400 150 250 400 400 100 350 85C Typ 2.8 530 510 0 100 200 645 645 Max Unit GHz ps ps ps ps ps
October 2001 * REV - 2
www.azmicrotek.com 3
AZ10EL31 AZ100EL31 PACKAGE DIAGRAM SOIC 8
NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm.
DIM A A1 A2 A3 bp c D E e HE L Lp Q v w y Z
MILLIMETERS MIN MAX 1.75 0.10 0.25 1.25 1.45 0.25 0.36 0.49 0.19 0.25 4.8 5.0 3.8 4.0 1.27 5.80 6.20 1.05 0.40 1.00 0.60 0.70 0.25 0.25 0.10 0.30 0.70 8O 0O
INCHES MIN MAX 0.069 0.004 0.010 0.049 0.057 0.01 0.014 0.019 0.0075 0.0100 0.19 0.20 0.15 0.16 0.050 0.228 0.244 0.041 0.016 0.039 0.024 0.028 0.01 0.01 0.004 0.012 0.028 0O 8O
October 2001 * REV - 2
www.azmicrotek.com 4
AZ10EL31 AZ100EL31
PACKAGE DIAGRAM TSSOP 8
NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm.
DIM A A1 A2 A3 bp c D E e HE L Lp v w y Z
MILLIMETERS MIN MAX 1.10 0.05 0.15 0.80 0.95 0.25 0.25 0.45 0.15 0.28 2.90 3.10 2.90 3.10 0.65 4.70 5.10 0.94 0.40 0.70 0.10 0.10 0.10 0.35 0.70 6O 0O
October 2001 * REV - 2
www.azmicrotek.com 5
AZ10EL31 AZ100EL31
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
October 2001 * REV - 2
www.azmicrotek.com 6

▲Up To Search▲

Price & Availability of AZ100EL31

	To Download AZ100EL31 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .